Frigidaire FPDS3085PF Bedienungsanleitung PDF herunterladen

p/n 807880605 Rev B (02/14)

SERVICE DATA SHEET

Electric Ranges with ES575 T3 Electronic Oven Controls

NOTICE

- This service data sheet is intended for use by persons having

electrical and mechanical training and a level of knowledge of these

subjects generally considered acceptable in the appliance repair trade.

The manufacturer cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important

that safe servicing practices be observed. The following are examples, but

without limitation, of such practices.

1. Before servicing or moving an appliance remove power cord from electrical

outlet, trip circuit breaker to OFF, or remove fuse.

2. Never interfere with the proper installation of any safety device.

3. GROUNDING: The standard color coding for safety ground wires is

GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not to be

used as current carrying conductors. It is extremely important that the

service technician reestablish all safety grounds prior to completion

of service. Failure to do so will create a potential safety hazard.

4. Prior to returning the product to service, ensure that:

• All electric connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp

edges, high-temperature components, and moving parts.

SERVICE DATA SHEET

Electric Ranges with ES 530 Electronic Oven Controls

• All uninsulated electrical terminals, connectors, heaters, etc. are adequately

spaced away from all metal parts and panels.

• All safety grounds (both internal and external) are correctly and securely

reassembled.

Oven Calibration

Set the electronic oven control for normal baking at 350°F. Obtain an average

oven temperature after a minimum of 5 cycles. Press Stop/Clear/Cancel to end

bake mode.

Temperature Adjustment

1. Set EOC to bake at 550°F.

2. Within 5 seconds of setting 550°F, press and hold the bake pad for

approximately 15 seconds until a single beep is heard (longer may cause F11

shorted keypad alarm).

3. Calibration offset should appear in the display.

4. Use the slew keys to adjust the oven temperature up or down 35°F in 5°F

increments.

5. Once

desired (-35° to 35°) offset has been applied, press Stop/Clear/

Cancel.

Note: Changing calibration affects normal Bake mode. The adjustments made will

not change the Self-Cleaning cycle temperature.

Resistance (ohms)

1000 ± 4.0

1091 ± 5.3

1453 ± 8.9

1654 ± 10.8

1852 ± 13.5

2047 ± 15.8

2237 ± 18.5

2697 ± 24.4

Open circuit/infinite resistance

RTD SCALE

Temperature °F (°C)

32 ± 1.9 (0 ± 1.0)

75 ± 2.5 (24 ± 1.3)

250 ± 4.4 (121 ± 2.4)

350 ± 5.4 (177 ± 3.0)

450 ± 6.9 (232 ± 3.8)

550 ± 8.2 (288 ± 4.5)

650 ± 9.6 (343 ± 5.3)

900 ± 13.6 (482 ±7.5)

Probe circuit to case ground

ELECTRONIC OVEN CONTROL (EOC) FAULT CODE DESCRIPTIONS

Note: Generally speaking “F1x” implies a control failure, “F3x” an oven probe problem, and “F9x” a latch motor problem.

Code Condition / Cause Suggested Corrective Action

F10

Control has sensed a potential runaway oven

condition. Control may have shorted relay, RTD

sensor probe may have a gone bad.

Check RTD sensor probe and replace if necessary. If oven is overheating, disconnect power. If oven

continues to overheat when power is reapplied, replace the EOC.

F11

Shorted Key: a key has been detected as pressed

(for a long period) will be considered a shorted

key alarm and will terminate all oven activity.

1. Press Cancel key.

2. If fault returns, replace the keyboard (membrane).

3. If the problem persists, replace the EOC.

F13

Control's internal checksum may have become

corrupted.

1. Press Cancel key.

2. Disconnect power, wait 10 seconds and reapply power. If fault returns upon power-up, replace EOC.

F14 Misconnected keyboard cable.

1. Disconnect power. Verify the

cable connection between the keyboard membrane and the EOC

on J2 and J3.

2. If the problem persists, replace the EOC.

3. If the connection is good but the problem persists, replace the keyboard (membrane switch).

F15 Controller self check failed. Replace the EOC.

F20

Control had detected a problem with the

communication link with the ESEC.

1. Check connection between P6 on EOC and P7 on ESEC-UIB.

2. If problem persist, replace ESEC-UIB.

3. If all above steps failed to correct situation, replace EOC.

F30

Open RTD sensor probe/ wiring problem. Note:

EOC may initially display an "F10", thinking a

runaway condition exists.

1. Check wiring in probe circuit for possible open condition.

2. Check RTD resistance at room temperature (compare to probe resistance chart). If resistance does

not match the chart, replace the RTD sensor probe.

3. Let the oven cool down and restart the function

4. If the problem persists, replace the EOC.

F31 Shorted RTD sensor probe / wiring problem.

F62 Missing zero-cross signal. Replace the EOC.

F90

Door motor mechanism failure. The controller

does not see the motor rotating.

1. Press Cancel key.

2. If Cancel key does not eliminate problem, turn off power for 30 seconds, then turn on power.

3. Check wiring of Lock Motor, Lock Switch and Door Switch circuits. 4) Unplug the lock motor from

the board and apply power (L1) directly to the Lock Motor. If the motor does not rotate, replace

Lock Motor Assembly.

4. Check Lock Switch for proper operation (do they open and close, check with ohmmeter). The

Lock Motor may be powered as in above step to open and close Lock Switch. If the Lock Switch

is defective, replace Motor Lock Assembly.

5. If all above steps fail to correct situation, replace the EOC in the event of a motor that does not rotate.

F95

Door motor mechanism failure. The motor does

not stop rotating.

1. Press Cancel key

2. Turn power off for 30 seconds then turn power on. If the door motor never stops rotating, or if the

F95 error comes back again, verify wiring of the motor. If wiring is good, replace the EOC.

3. If the problem persists, replace the motor door latch assembly.

P12

P11

L2 IN

BROIL

CONV

BAKE

L2 OUT

OVEN CIRCUIT ANALYSIS MATRIX

On Relay Board On Display Board

ELEMENTS

Conv

Fan

J3-5

Oven

Light

J3-3

Door

Motor

J3-4

DLB

L2 out

Cooling Fan

Relay 1

J3-2

Cooling Fan

Relay 2

J3-1

Door Switch

P11-3 / P11-4

Bake

Broil

Conv

P11

Bake

X X X* X X X

Broil

X X X X

Convection Bake

X X X X X X

Convection Roast

X X X X X X

Convection Broil

X X X X X

Clean

X X X X X

Locking / Unlocking

Light

Door Open

Door Closed

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION ENCLOSED

REPLACE CONTENTS IN BAG

ELECTRONIC SURFACE ELEMENT CONTROL (ESEC) FAULT CODE DESCRIPTIONS

E013 Bad EEPROM. Replace ESEC-UIB.

E014 Loss of Display tail #0. Check connection P1 on ESEC-UIB and P1 on ESEC Rotary HI Board (RR).

Loss of Display tail #1. Check connection P2 on ESEC-UIB and P2 on ESEC Rotary HI Board (RF).

Loss of Keyboard Tail. Check connection J2 on ESEC-UIB and J8 (RF).

E015 ESEC self test failed.

An E015 error code may indicate the ESEC-UIB is not receiving a synchronization signal from the

ESEC-Relay Board.

Check

if J2 pin 5 on the ESEC-Relay Board is wired to P4 pin 5 on the ESEC-UIB. If wiring is good and

the problem is still there, replace the ESEC-UIB. If the problem persists, replace the ESEC-Relay Board.

Electronic Oven Control (rear view)

DRAWER THERMOSTAT

1 2 3 4

Inhaltsverzeichnis

Seite 1 - IMPORTANT

p/n 807880605 Rev B (02/14)SERVICE DATA SHEETElectric Ranges with ES575 T3 Electronic Oven ControlsNOTICE - This service data sheet is intended for us

Seite 2

General Troubleshooting Schematic

Seite 3

p/n template Rev x (12/11)p/n 807880606 Rev B (13/11) Résistance (ohms)1 000 ± 4,01 091 ± 5,31 453 ± 8,91 654 ± 10,81 852 ± 13,52 047 ± 15,82 237 ± 1

Seite 4 - Schéma de dépannage général

Schéma de dépannage général

Weitere Dokumente für Küche Frigidaire FPDS3085PF

Um das Dokument anzuzeigen Frigidaire FPDS3085PF Bedienungsanleitung

Frigidaire FPDS3085PF Bedienungsanleitung (48 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Frigidaire FPDS3085PF Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Küche Frigidaire FPDS3085PF herunter. FRIGIDAIRE FPDS3085PF Manuel d'utilisation Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Küche Frigidaire FPDS3085PF

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küche Frigidaire FPDS3085PF